Smitty's RV-9A - Experimental Aircraft from Van's Aircraft The RV-9A from Van's Aircraft  
Howdy Ya'll
Howdy! I building an RV-9A! I'm an aviation nut and am excited about building my RV-9A from Van's Aircraft. Have a look around!
Smitty on FaceBook
Smitty on Twitter
Smitty on YouTube
Do what yer' Momma said...
Go Play!
Navigation
Homepage
Log Search
RV How-to Videos
RV TOOLS & BOOKS!
Places to FLY your RV!
Aviation Videos!
RV Resources
Become a PILOT!
RV-7/9 Drawings
ID: Pswd: RV-6A RV6A RV6 RV-6A RV7A RV7 RV-9A RV-9 RV9 RV-8A RV-8 RV8 RV-10 RV10 aviation aircraft Van's Aircraft RV8 RV8A RV-8 RV-8A RV-6 RV6 RV-6A RV6A RV-9 RV-9A RV9 RV9A RV10 RV-10 aopa eaa aviation experimental homebuilt airplane aircraft plane oshkosh
RV Construction Log
Preparation
Empennage
- Horizontal Stabilizer (49:40)
- Vertical Stabilizer (21:15)
- Rudder (32:15)
- Right Elevator (35:45)
- Left Elevator (30:50)
Wings
- Inventory & Setup (9:30)
- Left Wing Prep (54:30)
- Left Fuel Tank (45:20)
- Left Wing Skins (46:10)
- Right Wing Prep (34:15)
- Right Fuel Tank (47:50)
- Right Wing Skins (40:15)
- Ailerons (54:30)
- Flaps (40:30)
- Rods and ends (18:45)
Fuselage
- Fuselage Parts List
- Inventory and Setup (7:15)
- FireWall (14:30)
- F-704 Bulkhead (13:25)
- F-705 Bulkhead (14:20)
- Other Bulkheads
   and Longerons
(17:30)

- Tailcone (29:30)
- Center Section (35:15)
- Forward Section (52:40)
- Forward Assembly (24:30)
- Skins/Baggage Area (46:30)
- Seats & Seat Floors (30:15)
- Flaps & Gear Mounts (18:15)
- Fuselage Plumbing (14:0)
- Tail Feathers (16:35)
- Front Deck/Firewall (58:50)
Finish Kit
- Electrical (57:30)
- Electrical Part 2 (24:0)
- Canopy (22:30)
- Landing Gear (18:35)
How I Did Stuff
Pop-Rivet Dimpler 101
My Wing Jig
My Wing Cradle
Wing Cradle Mod
Tilting Tank Jig
Delrin Aileron Stops
Nutplate Preparation
Fiberglass 101
Events and News
Aviation Events
Aviation Events Around Texas
Fun Places To Fly in Texas
Aviation News
RV Groups & Support
Rivet Bangers
Van's Air Force
RV Information
How to Land an RV
Van's Aircraft
RV Resources
RV Photo Album
Completed RV-9's
RV-7/9A Drawings
Nut & Bolt Torque Values
Misc Goodies
Fuselage Parts List
How to Land an RV
My Tools
Fix a Heavy Wing
Paint Possibilities
Share on:
Share this! Twit this! 
Hauled everything to the hangar
Time for assembly! I cut two more 3 foot 2x4's and screwed them to the bottom of each plywood pieces. I will attach some wheels to the bottom of these 2x4ís later. They also help line things up when putting in the main 2x4 support and angle braces. Then I cut the main support beam from a 10 foot 2x4, making it 8 feet, 7 1/2 inches long, which connects the two plywood ends together. The plans call for the cradle to be approximately 9 feet long. So I subtracted the width of the 2 2x4's and the 2 plywood ends to come up with the 8 foot 7 1/2 inch measurement for the support beam. (NOTE: If you building an RV7 or RV8, the main support beam 2x4 is one foot shorter.) I put in 2 long wood screws through the back of the plywood into the 2x4 main support, to hold everything together.

HELP FOR THE HOMEBUILDER

A website designed for Van's Aircraft Homebuilders, helping them find the information they need to build the most dynamic aircraft in the world.
The "cover your butt" section
This website was built to document the construction of an RV-9A in compliance with the FAA requirements needed to certify the aircraft. Any experiences and/or comments are by no means to be considered as instructions on how to build an RV-9A or any other aircraft.
This is website is owned and published by OpenAirNet, Inc. © 2015. All rights reserved.
Cool Stuff
How Far is that Airport?